Wear Prevention: Outlane Mylar Protection

Honestly; I’ve been neglecting my Stern Star Trek Pinball machine. I got it new-in-box and didn’t do anything to protect the outlane hole which feeds the ball trough. My machine has seen some play at various conventions like Texas Pinball Festival since I purchased it back in 2016. The issue is that the steel balls tend to wreck havoc with the clearcoat and wood under the clear coat. I helped mitigate this problem shortly after unboxing by installing a set of Cliffy protectors. At the time; Cliffy did not offer an outhole protector so my ball return hole did get any love. A couple of weeks ago; I looked and noticed some wear on my outhole. 🙁

Stern Star Trek Outhole wear

You can see definite wear on the front and left side edges. It’s not massive; but enough to warrant some protection. I debated getting a new Cliffy outlane protector; but it only protects the front side from wear. As a result; I decided to try my hand at designing my own protector which would be cut out of 2mil adhesive Mylar (polyethylene) using my new Vinyl cutter.

I began by tracing the area with tracing paper so I could get the basic layout easily into the computer. I didn’t have a lot of room to work with so I decided to bring the mylar up to the black keyline just above the out hole. This would give me a little extra grip and make it easy to hide within the art work. I also decided I would wrap the mylar around the outlane hole pinching it between the ball trough and the underside of the Playfield. Finally; I would protect all three sides of the outhole to the metal ball guide seen the foreground. Finally; I decided to protect the outside corners of the PF in a similar way to protect the edges leaving cutouts for the legs of the metal ball guides so they wouldn’t “wrinkle” when the guides were re-installed. This was my initial design – and remains the my property (read: copy protected):

Copyright 2019 - Outhole
Stern Star Trek Outhole – Mylar

My design choices were to add the round corners created by the endmill when the Playfield was created and then add rounded Vs on the lines were the mylar would roll onto another perpendicular surface. This should aid in preventing wrinkles from forming at those junction points.

With the design created; there wasn’t anything else to do but cut it on the vinyl cutter and install it. It’s going to be very hard to photograph this crystal clear mylar but hopefully you can see it if you click on the pictures to get a higher rez image. Here’s the top surface with the mylar installed:

Copyright 2019 - Outhole
Stern Star Trek Outhole – Top

You can barely make out the outline of the mylar along the black keyline as designed. Additionally you can see the mylar where it wraps around the outhole sides and the two sides of the PF. Hear’s a close-up of the mylar wrapping around the PF:
Copyright 2019 - Outhole
Stern Star Trek Outhole – Wrap Around

Finally; the underside of the pf; where the mylar wraps around to be pinched by the ball trough:
Copyright 2019 - Outhole
Stern Star Trek Outhole – Ball Trough

I reinstalled the ball trough, all the ball guides, and put it back together. No issues what-so-ever with the installation and the mylar has no noticeable impact to the ball. Additionally; this should help minimize any additional damage to the clearcoat near the outhole.

If you are interested in a protector for yourself; I’m offering them forsale at my webshop: Stern Outhole protector – Mylar

Stern Star Trek: Custom Shooter Knob & Housing

A customer of mine graciously agreed to sell me his Shooter housing decal from aurich‘s Alternate decal set; as a result, I was able to finally finish my custom shooter housing and knob.

custom Star Trek Knob
custom 50th Anniversary Shooter Knob – Stern Star Trek

I had a shooter housing custom powder coated LE blue and installed the Decal. The knob is 3D printed at Shapeways from my custom design:

in polished Nickel and I powder coated it LE blue to match the housing.

A Star Trek 50th Anniversary Pin was then JB welded to the knob and it was encased in EasyCast Clear Casting Epoxy to give it a smooth surface for the palm of your hand.

Overall; I’m very happy with how it turned out.